HEAVY DUTY BUMPER
Bumper is the first fender profile that represents the perfect alliance between lightweight and power. Developed with a Patented triple structure of PVC, it has wide inner air gaps creation absorption of impacts never been reached before.
Impossibile caricare il modello 3D
Easy installation
Thanks to its unique threepieces design, Bumper can be easily installed. The two lateral components form the base and are joined by the Stainless Steel or Aluminum bar. The central insert is fitted by pressure.
Suitable for
- Yachts
- Pleasure boats
- Tenders
- Military boats
- Commercial boats
- Workboats
- Dock protection
- Pier protection
Features
Installation
PVC Ral colours
Finish / Materials
316 L Stainless Steel 
Aluminum Series 3 pieces
Available in reels cut to size | Description | Series | Item | Colours | Weight | Min bending Rad | Packaging | Min. order |
|---|---|---|---|---|---|---|---|
| Bumper 100 | 3 pieces | 130-110-100 | -B -G -W | 135 oz/yd 3.800 g/m | 5-1/2” 140 mm | coil | Special Order |
| Bumper 125 | 3 pieces | 130-110-125 | -B -G -W | 180 oz/yd 5.100 g/m | 5-7/8” 150 mm | coil | Special Order |
| Bumper 150 | 3 pieces | 130-110-150 | -B -G -W | 240 oz/yd 6.700 g/m | 6-1/4” 160 mm | coil | Special Order |
| Bumper 160 | 3 pieces | 130-110-160 | -B -G -W | 310 oz/yd 8.850 g/m | 7-1/8” 180 mm | coil | Special Order |
S/S bar & Aluminum bar
Available in reels cut to size | Description | Item | Weight | Length | Height |
|---|---|---|---|---|
| S/S bar - Bumper 100 and 125 | 130-110-165 | 10 oz/yd 300 g/m | 7’ 2 m | 1” 25 mm |
| S/S bar - Bumper 150 and 160 | 130-110-170 | 12 oz/yd 350 g/m | 7’ 2 m | 1” 25 mm |
| Aluminum bar - Bumper 100 and 125 | 130-110-185 | 4 oz/yd 135 g/m | 7’ 2 m | 1” 25 mm |
| Aluminum bar - Bumper 150 and 160 | 130-110-190 | 5 oz/yd 162 g/m | 7’ 2 m | 1” 25 mm |
Flat surfaces
For installation on flat surfaces
BUMPER 100 
BUMPER 125 
BUMPER 150 
BUMPER 160 Fitting steps
Bumper consists of three sections in pvc and a pre-drilled Stainless Steel installation bar.
Lay the profile on the ground around the boat or on the boat itself, the more the profile is properly stretched, the easier it is to install it.
For installations on aluminum boats, we suggest the use of aluminum accessories.
Place the fender profile and the steel bar and mark the correct position of the bar with a felt-tip pen. Drill holes in the boat using the holes in the bars as a guide and start the track screws over the entire circumference of the boat. Do not fully tighten at this time, you will need to first install the base modules in Step #3.
The 2 sections that make the base must be placed perfectly under the steel bar. The two base modules are attached, finish tightening the screws on the steel bar down to complete the full base installation.
Install the central insert by hitting it with a rubber hammer.
Fixe the extremities of the profile with one or two screws and finish with the end caps, which must partially overcome the end of the profile (they must not be fixed on its side).
Accessories
PVC end caps
| Description | Item | Colours |
|---|---|---|
| PVC end cap - Bumper 100 | 130-500-096 | -B -G -W |
| PVC end cap - Bumper 125 | 130-500-097 | -B -G -W |
| PVC end cap - Bumper 150 | 130-500-098 | -B -G -W |
| PVC end cap - Bumper 160 | 130-500-099 | -B -G -W |
Black S/S end caps
Black 316 L Stainless Steel | Description | Item |
|---|---|
| 90° Black S/S end cap – Bumper 125 | 130-500-587-BL |
| 90° Black S/S end cap – Bumper 150 | 130-500-588-BL |
| 90° Black S/S end cap – Bumper 160 | 130-500-589-BL |
Downloads
